Skip to content
Based on the Deluge Manual – Amadeus Edition (draft). Being updated for community firmware up to C1.3.

11.7 Reverb

Deluge’s reverb applies to the entire song as a send / return effect. Only the amount for each individual part can be adjusted. Reverb emulates the characteristics of a room and its shape. In the real world, audio bounces and ricochets through the room and between walls. Different rooms therefore have different characteristics giving the sense of space and distance.

An emitted sound will be heard followed by the initial reflections, for example direct from the walls within approx 100ms. Subsequent reflections typically where sound bounces between walls will follow. The room size and shape will therefore affect the reverberant sound.

Sets the amount of signal sent to the reverb. This is specific to each sound, synth, etc while all other parameters are common across sounds, instruments and song. Amount range: 0-50.

Pans the reverb signal left and right within the stereo-field. Range is 32L-0-32R.

Sets the spread of the reverb giving a wider stereo effect. Range is: 0-50.

Emulates the softer elements of a room. For example, a crowd of people, furniture, curtains all absorb rather than reflect sounds. Dampening gives a warmer feel, reducing higher frequencies from the reverb tail.

Sets up the room size emulation. Larger rooms would provide longer delays on the reflections. Range: 0-50.

Sidechain settings for reverb. This is a dedicated sidechain for the reverb output, but still utilises the same source as per the generic sidechain compressor.

  1. Clip view, ensure the clip is in-focus, example: a kit.
  2. Press Shift + REVERB pad, reverb shortcuts are as below
    • Pan
    • Width
    • Dampening
    • Room Size
    • Reverb Sidechain
    • Amount
  3. For the selected parameter, turn Turn SelectSelect to adjust the value.

or

  1. Ensure focus is clip view for a synth or kit.
  2. Access the effects within the menu’s. Press SelectSelect.
  3. Navigate in the menu to the FX section and press SelectSelect.
  4. Navigate in the menu to the ‘REVERB’ section and press SelectSelect.
  5. Select either ’AMOUNT’, ‘ROOM SIZE’, ‘DAMPENING’, ‘WIDTH’, ‘PAN’, ‘REVERB SIDECHAIN’. Press SelectSelect for the parameter to select.
  6. Adjust the value of the selected parameter by turning SelectSelect.
  1. Clip view, ensure the clip is in-focus, example: a kit.
  2. Press Shift + REVERB Amount.
  3. For the selected parameter, turn Turn SelectSelect to adjust the send value.

or

  1. Ensure focus is clip view for a synth or kit for selected sound.
  2. Access the effects within the menu’s. Press SelectSelect.
  3. Navigate in the menu to the FX section and press SelectSelect.
  4. Navigate in the menu to the ‘REVERB’ section and press SelectSelect.
  5. Select ‘AMOUNT’. Press SelectSelect for the parameter to select.
  6. Adjust the value of the send amount by turning SelectSelect.

or

  1. Ensure in clip view for a kit, synth.
  2. Press Sidechain/Reverb affect button. Button illuminates orange.
  3. turn lower Turn GoldGold to change reverb amount.
  1. Ensure in clip view for a kit, synth.
  2. Press Sidechain/Reverb affect button. Button illuminates orange.
  3. Press lower GoldGold to toggle reverb preset between: ‘LARGE’, ‘SMALL’, ‘MEDIUM’.
  1. Clip view, ensure the clip is in-focus, example: a kit.
  2. Access the effects within the menu’s. Press SelectSelect.
  3. Navigate in the menu to the FX section and press SelectSelect.
  4. Navigate in the menu to the ‘REVERB’ section and press SelectSelect.
  5. Select ‘REVERB SIDECHAIN’. Press SelectSelect for the parameter to select.
  6. Select ‘VOLUME DUCKING’. Press SelectSelect for the parameter to select.
  7. Adjust the level by turning SelectSelect.
  8. Options are auto, 0-50.
    • AUTO takes its parameters from the sidechain compressor of the sound with the highest reverb.
    • 0-50 Takes parameters from as per the normal sidechain setting. The reverb sidechain allows sidechain compression to be applied to the reverb trails. Deluge achieves this even with a common reverb, by using the sidechain compression parameters of the sound with the most reverb and applying them to the reverb itself. This is the auto setting and typically results in a pleasing and typical sound. Alternatively, the reverb’s sidechain compression settings can be manually overridden in the sound editor if desired.

Digital reverb model and low-pass filter C1.3

Section titled “Digital reverb model and low-pass filter ”